Skip to main content

500 heddles

It's finally done.

I've made all the heddles i think i really need for the castletown loom, and i'm going to go in and warp it up on saturday. or maybe friday. friday might be better now i come to think of it.

anyway, i got some yarn for to put on the loom. a navy blue plain yarn, probably something like 28 worsted count i guess, and also a brown and white sorta flecky nep yarn. i think that's the right term, i really should know these things by heart now.

anyway, i'm going to warp it up at 20epi or so with blue predominating in a sort of tartan check. so, my rough calculations go like this:

500/20 = (5/2=2.5x10=25) 25"

or just over 2 feet. allowing for draw-in it could end up being exactly 2 feet wide, which is quite a nice width for a scarf. so i guess i'll make a 5 metre warp with that and get 4 scarves out of it if all goes well

anyway, that's that. making 500 heddles is no joke.

-andrew

Comments

Meg said…
Well done, you! And your descriptions suits me just fine. I get the picture.
Andrew Kieran said…
my camera's still broken. i need to buy a set of tiny screwdrivers. and i always took lousy pictures anyway, me owning that phone is like the writers coronation street owning pens and word processors.

could be put to better use ;)

anyway, i've inherited my dad's old camera. i just haven't charged the batteries for it yet. it's smaller and can fit in my coat pocket without breaking, so it's all good
Trapunto said…
What a job. Did you figure out how long it took you to tie each heddle, and multiply by 500? I always like to do that after a monotonous chore. I'm not sure whether knowing total time spent increases or decreases my sense of accomplishment.
Andrew Kieran said…
nah. i did it in front of the telly in the evening. i guess it's not important, cos it's something you only have to do once for each loom.

also, timing the making of an individual heddle and multiplying by 500 would give an inaccurate result, as the time taken to make each heddle could vary by a second or two, and over 500 that'd skew your results quite significantly.

also, i was cutting the length up first, and then tying them (division of labour, innit), so i don't think i could reliably time the time

the better thing to do would be to time the making of the whole set and divide the time by 500, thus arriving at the average time it takes to make a heddle.

it remains to be seen whether i can put together a warping stand (i've got the frame) and warp a loom in one day though.
that's is quite a bit of work, good on you!!! I can't wait to see what your first project will be.
Dorothy said…
Hope your weaving with the flecky nep yarn is going well, great description I'm sure it's more use to me than a "name" for the yarn. You must be a fast knotter after 500 heddles.

Popular posts from this blog

Tablet Weaving Lesson #1: Backstrap weaving a simple diamond motif

This is the first in a series of video and photo tutorials showing basic to advanced tablet-weaving concepts. These lessons shall each build on the last and hopefully take the viewer from simple diamond patterns up to more complicated double face pattern weaving with finer yarns and eventually onto the heady heights of brocading and other fancy techniques (just as soon as I learn how to do them myself). In this first lesson we'll learn the basic weaving steps involved in weaving a diamond pattern in the backstrap style. This lesson is meant for someone who has purchased a ready-made warp from me. The next lesson shall detail how to design and make this warp oneself. And we begin This is the basic pattern we are making. The woven band is tied to my waist with another strap. I am holding a small stick shuttle in my right hand which contains the weft. In front of me are the cards, each card has 4 warp threads going through it. The gap that you can see is called the

The curse of the faulty rachet-stop + The contractual obligation video post

I got the warp wound on the medium sized loom last week, and threaded and sleyed it this weekend Now. The back beam is held by a ratchet. and the ratchet-stop is a plate of metal which is pulled up from the ratchet-wheel with a handle attached to the main upright. It seems that somewhere along the line of the last couple of weeks i must have bent the plate back a little cos it no longer holds tight against the wheel. i've tried holding it down with a piece of cord wrapped round the beam, but it's not having it and i've had the whole thing come loose while swinging the batten twice already. I've tried to remove the plate but one of the screws is held tight. I'm going to have to take it outside and hammer it flat on the doorstep. This is aggravating On another aggravating note, the shuttle keeps flying out of the race and hitting the wall when i beat from the left hand side on the larger loom and i can't figure out why, cos i haven't changed anything from the

treble-cloth construction

I am currently in the process of designing a triple layered fabric. One layer shall carry conductive warp threads (one out of every three), another layer shall carry conductive weft threads (again, one out of every three) and a third layer shall lay between them and act as an insulator, keeping them apart and preventing unwanted contact between the two conductive layers. Constructing a treble cloth is a compicated process. The way that a treble cloth is woven is that first the face cloth is woven, then the centre cloth is woven, then the back cloth is woven. This is a draft for a treble cloth. The crosses indicate weaving marks for the cloth currently being woven, the dashes are lifts and are used to indicate shafts that are being lifted in the case of layers that are above the layer currently being woven. Blue is back, Red is front, Green is centre (All three layers are plain weave btw) The cloth is constructed like so 1: Back cloth is woven. All red and green marks are lif